深圳廠房裝修環氧樹脂地板漆的保養維護的方法
  深圳廠房裝修環氧樹脂地板漆的保養維護的方法，在施工及維護方面濰坊地坪漆建議作如下處理：
  一、深圳廠房裝修環氧樹脂地板漆養護要求：
  1、清潔地面時請用軟質拖把或干濕兩用吸塵器，可用清水或清潔劑清洗，但請注意地面濕滑;
  2、表面保潔,環氧地坪表面清洗方法簡便，一般用水擦洗。如遇難清洗的污漬，使用清洗劑即可，也可用工業去脂劑、除垢劑等，然后再用水沖洗干凈。對于相當頑固的污漬，也可用機械清潔的辦法，但對地面不要施壓、磨損過大以影響地面的平整及光澤。　　
  3、若因使用時間較長而造成磨損或刮花、小面積可進行局部修補，若面積較大則建議重新滾涂一次。
　4、凡進入車間人員須換鞋(以免將處面泥砂帶入車間而劃傷地面);
  5、推車，板車之車輪請用硬質或彈性膠輪，并廠房內外分開使用;
　6、避免化學品的污染　
  7、請勿濫用機械,使用時盡量避免對地面過重的敲擊，不要用非常重的或者堅硬的物品敲打地面，除非工作的需要，請避免頻繁的不必要的磨損。尤其是對于ESL地坪，為保持其光潔細致、外表美觀的優點，特別注意避免鋼輪等的交通;不要有過重的交通及負載，與地面接觸處要注意避免產生劃痕。
  8、凡是硬件：如鐵椅、鐵桌、鐵貨架等，須將其腳用軟質塑料或橡膠包裹以免在使用過程中劃傷地面;
  二、深圳廠房裝修環氧樹脂地板漆施工方法：
  基面打磨、裂縫修補→環氧底漆一道→批刮環氧砂漿層→環氧膩子層→環氧色漆層→環氧罩光層
  三、深圳廠房裝修環氧樹脂地板漆施工環境：
  基面含水率：在6%以上時不能施工非水性環氧地坪;2.空氣中濕度：在85%以上應停止施工;3.施工溫度：低于5℃應選用特殊配方。對于一些大型的車間廠房或者車庫等區域的地面處理方式，都會采用環氧地坪漆來使用，為了環氧地坪能有表面良好的光潔度和美觀的效果。
　深圳廠房裝修環氧樹脂地板漆的保養維護的方法由深圳祥云裝飾設計工程有限公司分享，如果大家喜歡轉載請注明出處：http://boshengdazs.com/。　
  Shenzhen factory decorate epoxy floor paint the maintenance method
  Shenzhen factory building decoration epoxy floor paint, the method of the maintenance of the construction and maintenance of weifang floor lacquer Suggestions as follows:
The, shenzhen factory decorate epoxy floor paint maintenance requirements:
  1, please clean the ground with soft mop or dry wet amphibious vacuum cleaners, available water or cleanser, but please note the ground wet.
  2, surface cleaning, epoxy floor paint surface cleaning method is simple, general water scrub. Such as killing cleaning besmirch, the use of cleaning agent can, also can use industrial degreasing agent, cleaner, etc., and then rinse  clean with water. For quite a stubborn stains, also can use mechanical cleaning solution, but don't pressure, wear and tear on the ground is too large to influence the leveling of the ground and luster.
  3, if due to use for a long time wear or scratches, small area can repair locally, if it is recommended to roll a larger area.
  4, who enter the workshop personnel shall change the shoes in order to avoid the surface mud into the workshop and scratch the ground);
  5, cart, wheels of scooter please use of rigid or flexible roller, and building internal and external used separately;
  6, to avoid contamination of chemicals
  7, please do not abuse machinery, when using, as far as possible to avoid heavy knock on the ground, don't use heavy or hard goods hit the ground, unless the needs of work, please avoid unnecessary wear and tear. Especially for ESLfloor, to maintain its bright and clean and meticulous, beautiful appearance, the advantages of paying special attention to avoid traffic such as steel wheel; Don't be too much traffic and load, contact with the ground should payattention to avoid the scratch.
  8, all hardware, such as iron chairs, iron table, iron shelves, etc., to its feet with soft plastic or rubber from scratch in the process of using the ground;
  Second, the shenzhen factory decorate epoxy floor paint construction method:
  Reference plane grinding, the crack repair - a epoxy primer - batch blows layer of epoxy mortar to epoxy putty layer - > epoxy paint, epoxy cover layer of light
  Three, shenzhen factory decorate epoxy floor paint construction environment:
  Base moisture content: not construction in more than 6% of waterborne epoxy floor; 2. The humidity in the air: above 85% should stop construction, 3. The construction temperature: less than 5 ℃ should choose special formula. For somelarge area of workshop workshop or garage, ground handling, using epoxy floor paint to use, in order to epoxy floor can have a good surface finish and beautiful effect.
  Shenzhen factory decorate epoxy floor paint the maintenance method of sharing by shenzhen xiangyun decoration design engineering co., LTD, if you like them reprint please indicate the source: http://boshengdazs.com/.